How exposure works

previous article: Making Google love your photo site next article: Dealing with negative critique

To understand exposure in photographical terms, EV is probably the single most important number you will have to understand, to understand the theory behind the art of photography. This goes from your tiniest, least significant compact camera, to your cock-on-the-table style medium format camera with a digital back.

Non-technical

Let us imagine a value called TCE. This TCE (The Correct Exposure) does not exist, because you might for a variety of reasons want a different exposure than the TCE. But for the sake of argument, let’s assume TCE exists, and this is what you will want when you take a certain picture.

To get a correct exposure, you will want to have EXACTLY the right amount of light to capture your image. Not too much, and not too little.

So, what is it that might affect how much light comes to the film or imaging chip?

Shutter speed – Imagine a mug with a lid containing a mysterious source of light, and the room you stand in is covered in darkness. Shutter speed would be how long you open the lid.
Aperture – Same cup, same concept, but this time, how far you open the lid (if you open it a little – small aperture, i.e. high aperture numbers (for example f/22). If you open it all the way – large aperture – i.e. low aperture numbers (for example f/2.8)
These are the two basic ones. The last factor that comes into play is your film speed, or the light sensitivity of your surroundings while holding the cup if you will.

That’s all there is to it – these three factors combined allow you to manipulate the light in all kinds of ways (big depth of field through small apertures, freezing motion through fast shutter times, etc).

So, to get TCE, you will want to combine these three factors into JUST the correct way. Now, if you replace TCE with TCEV (The Correct Exposure Value), you understand what I have been on about.

EV is a number describing an exposure – any exposure – regardless of its “correctness”.

Technical

The definition of EV=0 is an exposure of 1 second at f/1 using ISO 100 film, or any equivalent thereof (2 seconds f/1.4, 4 seconds f/2.0 etc)

The technical definition of EV is 2^EV = LS/C.

EV = the exposure value – explained above
L = field (or zone) luminance –
C = Exposure Constant – This is a constant that depends on what unit you are using to express the luminance (L)If you use candelas/ft², it is 1.3. If you are using candelas/m²*, it is 12.5*. If you use apostilb, it is 3,98.
S = film speed following the ISO standard

*) some of you might know cd/m² as lux or lumens/m²,

This also means that 2^ev = A²/T

A = the f-stop number of the aperture
T = shutter time in seconds

Combining these two; EV = log2(A²/T) = log2(LS/C) – which is the only formula you are likely to need, if you want to understand the basics of mathematics behind photography.

So what is the EV number used for?

Ah. Well, the EV number is used internally in cameras – an EV number of 10, for example, would refer to all the combinations of shutter times and apertures that would give a given exposure using ISO 100 film. This is useful, because a camera only has to add one thing to this equation; A light measurement. A camera with a lookup table or an algorithm to calculate the correct EV is all set for using all the different combinations that are able to give you the exposure you want.

But why would I care, if the camera handles everything?
Because the camera doesn’t always get things right. You may also want to use alternative exposures for artistic reasons.

Most cameras have an EV compensation wheel/dial, allowing you to choose how much you want to over/underexpose an image. This is usually measured in +/- 2EV, 1/3 steps. This means that you can over- or underexpose an image by two whole EV steps (which, incidentally, would mean the same as two full f-stops either way), in steps of 1/3 EV.

I hope that made things a little clearer – if not, leave a comment, and I’ll see what I can do!

Money made from this advert will be invested in prime lenses.

This post, "How exposure works", is part of these categories: All articles, Become a better photographer, was posted by Haje Jan Kamps and saw the light of day on the 1st of May 2008. I hope you liked it.

Insights, suggestions and comments

By Christopher Walrath on May 9th, 2008 (permalink)

I have to disagree. An exposure value is a set combination of shutter speed and aperture. Though different ISO rated films require a different set of exposure settings to attain the same amount of exposure, 1/60 @ f/5.6 is EV11 regardless as to whether ISO 50 or ISO 3200 film is being used. ISO is not a factor in determining the qualities of an exposure value.

By Julian Evetts on December 22nd, 2009 (permalink)

I disagree totally with Christopher Walrath, whilst I cannot speak for film ISO, with digital if 1/60 @ f/5.6 ISO 100
is the right exposure for an image and you change the ISO to 1000 that image will be over exposed. Simple as that.